To do this, locate the gas regulator valve. Doing this starts the flow of gas into the tube that supplies the pilot light.
How to light a water heater pilot light.
How to light a water heater with electronic pilot youtube. The traditional gas igniter is a standing pilot, and in the past, you had to light it by hand using a long match.contemporary richmond water heaters have sealed combustion chambers, though, so if they have standing pilots, they are equipped with piezoelectric spark igniters.before trying to relight the pilot, consult your owner's manual to make sure that there is a standing pilot. Continue to hold down the red button for one minute after the pilot is lit, and then release it. The first thing you want to do is to make sure the gas is turned off.
Honeywell produces an electronic ignition retrofit kit that is ideal for residential and light commercial gas furnace systems. How to light a water heater honeywell electronic gas control youtube. While still holding the gas down, light that pilot.
I was able to relight the light after it dried out about 24 hours later. If you are concerned about potentially dangerous damage, consider calling a plumber to do an inspection. If you have an older rv water heater that requires manual lighting, you will need to use a lighter (or match) to light the pilot.
This valve is usually found on the outside of your water heater where the main gas pipe enters the heater. Honeywell y8610u6006 gas valve intermittent pilot retrofit kit available here. Open the door/cover over the pilot light access.
Hold the pilot button down to “prime” the thermocouple—otherwise it will cut the gas supply to the pilot light. Turn the gas knob to “pilot,” press and hold it down. Standing pilot, the second one consumes more fuel regardless of when the furnace is used or not.
The most common issue that leads to repeated pilot outages is a dirty or bent thermocouple, which is a small copper wire and rod that senses the flame and automatically turns the. Let go of the igniter button, but keep pressing the pilot dial downward for around 30 seconds. Yes, it is most likely safe to use.
If your model has a separate button for pilot mode, press and hold it down. Hot water heater thermostat thermostt gs electric reset button. All pilots have a safety system that prevents the main gas valve from staying open if the pilot flame has gone out or the igniter has failed.
The new standard pilot water heater has a gas control status light and ignition button to lightning a water heater pilot with an ignition. If your water heater’s gas valve does not push down, look for a red control button near the valve. A condensing water heater uses two heat.
For safety reasons, do not attempt to light a water heater pilot manually if it uses an electronic igniter. You should hear a “whoosh” sound when the gas is lit. Some water heaters have a red or black igniting button and others need to be lit manually with a long lighter.
After that you can turn the burner knob to the on position and adjust the flame as you like. A pilot light is always burning while using a small amount of gas; The good news is that you can follow these 5 easy steps to reignite your hot water heater pilot light:
Either a water heater is running or not. Standing pilot, the latter runs continuously as long as the sensor registers the heat from the pilot light. Once there is a need for heating (or call from a thermostat), a gas control valve releases the gas into the main burner, and the pilot light ignites the gas.
One can still purchase a gas furnace or water heater with the old standing pilot ignition systems.these systems have been proven reliable and safe over time. Is it safe to use? Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit.
Turn the water heat dial to low and the on/off/pilot dial to pilot. Clear 4 blink fault code on honeywell water heater gas valve high. Can i light my rv water heater with a lighter?
This step initiates a flow of gas, which enables you to light the flame. While holding the gas knob or button down, light the pilot. Use a flashlight or a headlamp to find the burner inside.
This effectively shuts down the system, so you will get no heat from the appliance if the pilot is not working properly. Turn the gas valve to the pilot setting and push down on it. Gently turn the gas knob to the “pilot” setting and hold it down.
Depending on the model of water heater you have, you may have a red. Choosing the right one for your furnace An induced draft water heater is a type of water heater that uses a small fan, to draw the combustion gas from the combustion chamber.
Pilot light on water heater dhwanidhc com. The job of the pilot or igniter is to ignite the gas flowing from the main gas valve to the appliance burners. Then, turn the on/off/pilot dial downwards and push the igniter button at the same time.
A very small amount of water drained into my hot water heater and put the pilot light out. Induced draft water heaters use an intermittent pilot or hot surface ignition instead of a standing pilot light. When the flame ignites, continue to hold the gas knob or button down for a full minute.
Gas systems that are eligible for an upgrade from standing pilot to electronic ignition (covers btu ratings up to 270,000).